Skip to main content

Hardwood Flooring Installation in Nolensville, TN

You’ll see the new hardwood in morning sun, at the back door after a walk, and under the kitchen table every night. McGrath helps Nolensville homeowners compare grain, texture, and sheen in the rooms they’re planning to connect, then scopes the installation around those choices.

Refinished hickory boards with warm natural grain around a dark kitchen island

McGrath’s Hartog hickory project in Franklin, TN.

Compare several boards
Choose a finish you can maintain
Plan transitions between rooms

Choose the floor with your rooms in mind

Look at several boards together and take samples home. The same wood can read differently beside your cabinets, in direct sun, or in a hallway lit from one end.

Choose a sheen that suits daily wear

If paws, shoes, and chair legs use the same stretch of floor, compare matte and satin samples at floor level. Lower sheen reflects less light, so small marks can be less noticeable. Ask about the finish’s approved cleaner, and use felt pads and entry mats that suit that finish.

Compare samples at more than one time of day

Put the same boards next to the window and in the shaded parts of the room. Light changes how a color reads, and repeated sun exposure can change the wood’s color over time. Consider shades in the brightest rooms, and ask the manufacturer about when to lay rugs and which backings to use.

See how the pattern reads across a room

Knots, darker grain, and changes in color look different on several boards side by side. Ask what the grade allows and compare smoother and textured samples with a cabinet door or paint chip before choosing a whole room from one board.

Rick Says: Ask what the hardness number measures

The Janka number tells you how well the wood resists a dent. If you’re picturing dog claws by the back door, take a look at the finish, too. Lay a few samples where the light crosses the floor and look at them standing up. Ask what you’ll clean the finish with and what a touch-up would involve.

Hardwood in two adjoining Nashville rooms

Charles I. of Nashville shared that he replaced the carpet in his living and dining rooms with hardwood. He credited Rick with answering his questions and helping him select the product, and praised the installation crew’s workmanship.

Dark Hallmark Onyx Oak planks around a gray sectional and an area rug

Hallmark Onyx Oak room example, installed by Gramar Stone.

What a super-matte oak looks like

Hallmark’s True Collection Onyx Oak is a 7½-inch engineered European oak plank with a textured face and a Nu Oil® Super-Matte finish. Look at several boards together to see how the dark tone and grain look against your walls and furnishings.

Use the cleaner Hallmark approves for this finish. If you compare it with a site-finished hickory floor like the Hartog kitchen, ask how to care for each and what future touch-ups would involve.

What goes into your installation plan

Bring photos from the rooms

Show where the sun lands, where you come in with the dog, and which rooms need the same floor.

Compare wood and finish samples

We’ll put full boards side by side and discuss grain, color range, feel, and the care the finish requires.

Check what’s under the floor

We’ll identify the subfloor and discuss preparation, moisture checks, board direction, and how the new floor meets stairs or other surfaces.

Review the written scope

The scope should identify the wood and finish, removal, preparation, transitions, and timing before the order goes in.

Hardwood questions for Nolensville homes

Will matte hardwood show fewer marks from my dog?

A lower sheen usually makes fine marks less noticeable. Trim nails, use finish-compatible entry mats to catch grit, and ask how the maker recommends cleaning the floor.

What does character grade change?

It affects the look across the floor, including visible knots, grain, and changes in color. Look at several boards together to see how much variation you’re comfortable with.

Can I use the same hardwood from the kitchen to the living room?

We can assess both spaces for the same product. The subfloor, site conditions, and manufacturer’s requirements help determine where that floor can run and where a transition is needed.

When should I choose solid versus engineered hardwood?

Start with the room and what’s underneath it. Then compare products approved for those conditions. If refinishing later matters, ask about the actual thickness of the engineered wood’s top layer and what it can support.

Bring the rooms into the decision

Bring pictures of the rooms you’re connecting, plus a cabinet or paint sample if you have one. Tell us where the floor gets the most traffic and when the sun comes in. We’ll help you narrow the choices at our Franklin showroom before we check the installation details.

Flooring and cabinetry samples at McGrath Floor & Design’s Franklin showroom